Speedy Appliance Repair

Lights Dim When Appliance Turns On

Quick Contact

    Professional Appliance Repairs

    Lights Dim When Appliance Turns On

      Are you looking for an appliance repair technician near you in Toronto? Give us a call and we’ll send out one of our professionals right away!

      ☎️ (647) 952-2789

      While you may be compelled to check your vision, there is more than likely another reason why the lights in your house seem to dim from time to time.

      If you notice your lights getting dimmer when you turn an appliance on, there could be several reasons behind it.

      It could indicate a more severe problem that could pose a fire safety danger.

      Continue reading to find out why lights dim when appliances are turned on and what you can do to safeguard your home and family.

      Why Do the Lights Dim When You Turn on the Appliance?

      The diagnosis and repair are best left to the professionals when it comes to electrical problems.

      Handy homeowners may do a lot of do-it-yourself jobs on their own, but when it comes to electrical problems, it is best to leave it to the specialists.

      When it comes to issues with electricity, it is in your best interest to entrust the work to trained professionals in York.

      The following is a list of some of the most typical reasons why the lights dim when turning on the appliance.

      Reason One: Overloaded Circuits

      Check whether the lights are connected to the same circuit as the appliance to determine why they dim when you use them.

      Mainly if the device in question is a dryer, air conditioner, or microwave.

      It’s possible that you’re just dealing with an overloaded circuit.

      Wherein your circuit is either old and inefficient or configured to power more appliances than it can support.

      If you live in an older home, this is almost certainly your situation.

      Overloaded circuits, because of appliance use, are relatively frequent and, in most cases, do not provide a significant risk.

      However, if you notice that your lights are dimming even when the appliance is not being used or if the appliance is tripping the circuit breaker in your home.

      There may be another cause for the dimming.

      It’s time to call an appliance technician.

      Reason Two: Poor Wiring

      Check the wiring if the lights dim when you switch on the appliance.

      It’s also possible that this is the consequence of an electrical system malfunction, which poses fire and electrocution risks.

      Problems with the electrical system may be caused by improperly placed wiring and have knock-on effects on surrounding residences.

      If your lights are fading suddenly, it might be because your wiring is old, and you can’t manage the electricity.

      Contact your local utility provider and ask them to inspect the electricity lines if you are unsure whether this is the issue.

      Alternatively, a new transformer installed closer to the home might be the answer.

      If you cannot solve the issue on your own, you should contact an appliance repair expert at Speedy Appliance Repair.

      Reason Three: Corroded Neutral Wiring

      There may be a more severe issue at hand if the lighting in your home flickers between bright and low.

      Perhaps the neutral wire in your circuit breaker is frayed or damaged.

      There are three wires in a circuit breaker.

      One is colored red or black and is considered a hot wire, another is colored white and is considered “neutral,”.

      The third is colored green and is considered “ground” and is used only for safety.

      For your home circuit, the first two wires are what carry electricity.

      The neutral wire’s only function is to connect back to earth ground inside the electrical panel, completing the circuit.

      If the neutral wire is damaged, there will be a gap in the circuit’s return route to the electrical panel, which might lead to voltage differences between the two live wires.

      If your lights are becoming too bright, the voltage is too high, and if they are getting too dim, the voltage is too low.

      Your electronics risk being over or under-powered if the situation continues to deteriorate.

      Most accidents and fires are caused by faulty wiring or connections.

      Get in touch with an expert for home appliance repairs immediately.

      Safety First!

      Because of the inherent dangers of working with electricity, it is always best to have an appliance repair expert look into electrical problems.

      Do-it-yourself repairs are risky and might worsen the problem, so they’re never advised.

      Diagnosing problems on your own is risky since you might put yourself and your loved ones in harm’s way.

      When the lights dim when you switch on the appliance, it’s time to bring in an expert.

      If the light is flickering, there is an issue with the appliance, the wiring, or the circuit.

      It may also indicate a connection issue that, if left unresolved, might lead to a fire.

      Call Speedy Appliance Repair if the lights dim when appliance turns on.

      Conclusion

      Overloaded circuits or an electrical panel might be to blame if the lights dim whenever you switch on an appliance.

      It would help if you looked at your electrical panel to ensure it is not overloaded.

      Overloading a circuit may result in the tripping of the circuit breaker, which can, in turn, cause electrical shocks and potential damage to the connected equipment.

      If you can’t figure out why the lights dim when appliance turns on, it’s best to an appliance technician.

      Rate this post

      Recommended articles

      Contact Us
      COVID-19 NOTICE:
      Our technicians are equipped with masks and gloves complying with health and safety regulations.
      This is default text for notification bar